SIKAGROUT 212 PDF

9 May SikaGrout® 1. 1/4. C onstruction. SikaGrout® SikaGrout® High Strength shrinkage compensated cementitious grout. Product. Specialist Construction Supplies for Repair, Maintenance, Building & Infrastructure. Sikagrout Data Sheet. Specification notes. Product: Sikagrout SikaGrout DIVISION 3 – CONCRETE. Section – Grouts. Part 1 – General. Summary. A. This specification describes the grouting of cavities, voids.

Author: Tojakora Kagore
Country: Sao Tome and Principe
Language: English (Spanish)
Genre: Automotive
Published (Last): 22 February 2013
Pages: 479
PDF File Size: 4.82 Mb
ePub File Size: 14.30 Mb
ISBN: 535-6-96646-118-4
Downloads: 55732
Price: Free* [*Free Regsitration Required]
Uploader: Mikagor

Mix for at least 3 sikagrout 212 until a uniform, lump-free consistency is obtained. Wash hands immediately after use.

Bolt holes must be blown clear of dust and other debris, and anchor bolts must be degreased with a suitable solvent such as Kwiklean sikagrout 212 soluble solvent based cleaning compound.

The use of standard concrete curing techniques, such as light water fogging for 72 hours or the application of a suitable water based curing compound is recommended on all exposed surfaces of Sika Grout Sika Grout sikagrout 212 be used to fill 21 up to mm in depth.

For the structural grouting of: Do not commence fogging until initial set has been reached. Use either a slow speed drill set at – rpm with a clean, sikagrout 212 free, mixing paddle, standard mortar or concrete mixing equipment, or purpose built cement grout mixing equipment.

Width of gap to be grouted in mm. Dispose sikqgrout in accordance with sikagrout 212 regulations.

sijagrout Wash thoroughly with soap and water. The sikagrout 212 properties of Sika Grout will be severely reduced if heat is introduced to the mixed product via warm batching water, hot storage conditions of Sika Groutand high substrate and ambient temperatures.

In most cases, the bolt hole should be no greater than sikagrout 212 mm larger in diameter than the bolt.

A slight agitation of the bolt will assist the Sika Sikagruot to fill sikagrout 212 annulus evenly. Use of an approved dust respirator, safety goggles and chemical resistant gloves are recommended.

SikaGrout 212

Exercise care, as with handling any chemical construction sikagrout 212. Sikagrkut Sika Grout within 30 minutes of sikagrout 212. Add the required amount of water to the mixing vessel and then add Sika Grout Users should always refer to the most recent issue of the Technical Sikagrot Sheet for the product concerned, copies of which will be supplied on request, or can be accessed on the internet under www.

Remove affected person to fresh air immediately and contact a physician. In practice, the differences in materials, substrates and actual site conditions are sikagrout 212 that no warranty in sikagrout 212 of merchantability or of fitness for a particular purpose, nor any liability arising out of any legal relationship whatsoever, can be inferred either from this information, or from any written recommendations, sikayrout from any other advice offered. Centre or locate the bolt in the desired position, using shims if necessary, and then leave undisturbed until the Sika Grout has set.

Uncured material may be removed with water. Sika Grout is sikagfout one component, multi-purpose,freeflowing, expanding,cementitious grout.

SikaGrout – Everbuild

The quantity of aggregate xikagrout should not exceed one 1 part of aggregate to one 1 part of Sika Grout by weight. Place sikagrout 212 pre-determined quantity of Sika Grout directly into the bolt hole.

Sikagrout 212 Company reserves itself the right to change the sikagrout 212 of Sika products if so required by new research and development. Concrete surfaces must be clean, sound and free from oil, grease, cement laitance and all loosely adhering particles. Contains Portland cement and crystalline free silica.

Cured material can only be removed mechanically. The correct sikagrout 212 of Sika Grout sikagrout 212 to completely fill the annular gap between the bolt and the sides of the hole should be determined before installation is attempted. If the Sika Grout does not fill the annular gap evenly during bolt insertion, withdraw the bolt sikagrout 212 insert additional Sika Grout and re-insert the bolt.

Flush immediately with water for 10 – 15 minutes and contact a physician immediately. DO not attempt to add additional Sika Grout with the bolt in place. The proprietary rights of third parties must be observed. Water Requirements for SikaGrout sikagroyt After establishing the consistency required, determine the water requirement per 25 sikagrout 212 bag see Table 2.

Collect in appropriate container. Approximate Flow Distance in cm. Wash clothing before re-use.